Electrostatic influence machine · Patent application in preparation

An electrostatic machine built on the Pidgeon principle.

Two counter-rotating rotors with 32 sectors set in dielectric, collector combs feeding two Leyden jar stacks, and two Pidgeon inductor discs whose inductors cross without touching.

Explore the machine

Your machine notebook

Workshop

Online saving is unavailable in this preview. Download a draft to keep a local copy.

The inventor's hand-drawn sketch of the machine
The inventor's original sketch

The machine

How the parts are arranged

Angle reference: the vertical line is 0°. Angles to the left of it are counted as "left". Select a part to highlight it in every drawing.

Side view of the stack: inductor disc, comb, rotor 1, rotor 2, comb, inductor disc, with wiring to the Leyden jar stacks
Fig. 1 — Stack and wiring (side view). From the centre outwards: the two rotors, with a collector comb at each edge reaching over both rotors, then a Pidgeon inductor disc on each side, then an auxiliary inductor disc on each side (outermost, as in the sketch). All sector leads terminate in stationary contacts; the contacts touch the rotor sectors only as they pass.
Face view of the two rotors with 32 sectors each
Fig. 2 — The rotors (face view). Each rotor carries 32 sectors and turns in the opposite direction. All sector leads are stationary contacts: they stay fixed and touch each sector only as it passes. The left rotor has Pidgeon-inductor contacts near its upper-left side and along its left side below the collector comb. The first Leyden jar's outer foil also connects to a sector on the left side of the right rotor, below but offset from its collector comb, and is linked to the bottom side of the left rotor and the left Pidgeon inductor on the right-hand Pidgeon disc.
The two Pidgeon inductor discs and how their inductors cross
Fig. 3 — Pidgeon inductor discs. Each disc carries two inductors, oriented as in Pidgeon's original patent. Seen together, the inductors of the two discs cross each other but never touch directly.
Left auxiliary disc, left Pidgeon disc, rotors, right Pidgeon disc and right auxiliary disc with the described wire paths
Most-right Pidgeon inductorSecond-from-right Pidgeon inductorRight auxiliary route to right-rotor sectorMost-left Pidgeon inductorLeft disc's right Pidgeon inductorJunctionHorseshoe mouths point tangentially to the next inductor
Fig. 4 — Auxiliary discs and wiring (laid out like the sketch, left to right). The left auxiliary disc has 12 horseshoe inductors in four groups of three. Its bottom-left group is connected to its top-right group; together, those groups and the top-left group connect to the rightmost Pidgeon inductor. The bottom-right group connects to the left Pidgeon inductor on the right-hand Pidgeon disc, which also joins the first jar's outer-foil lead and the left rotor's bottom-side contact. On the right auxiliary disc, the top-left, bottom-right, and bottom-left groups connect to the right Pidgeon inductor on the left-hand Pidgeon disc and branch to a stationary right-rotor contact. The top-right group connects to the most-left Pidgeon inductor. All sector contacts remain stationary as the rotor sectors pass.

Follow a connection

Trace the circuit through Fig. 1 and Fig. 4

Fig. 1 shows the machine’s physical stack; Fig. 4 shows the described electrical routes. Choose an inductor to highlight its route in the wiring drawing and its corresponding disc positions in the stack view.

Select a route to highlight its described path.

Fig. 4 · interactive wiring tour

Step through the described connections

Advance through the diagram to highlight each described connection.

1 · Counter-rotating rotors
Two discs in the middle of the machine turn in opposite directions. Each has 32 sectors set in the dielectric.
2 · Collector combs
Each comb is a fork at the rotor edge with needles facing both rotors. The top collector comb is the positive output. The bottom collector comb is the negative output and connects to the inner foils of the Leyden jars.
3 · Leyden jar stacks
The jar stacks store the collected charge. Their inner foils connect to the collector-comb outputs. The first jar's outer foil is also linked to the left Pidgeon inductor on the right-hand disc and to stationary contacts on the left rotor's bottom side and the right rotor's left side.
4 · Jar outer-foil routes
The first Leyden jar's outer foil connects to a stationary contact on the left side of the right rotor, below the collector comb but offset from directly beneath it. That outer-foil lead also connects to the bottom side of the left rotor and to the left Pidgeon inductor on the right-hand disc. All contacts remain fixed and touch the sectors only as they pass.
5 · Pidgeon inductor discs
After the combs there are two Pidgeon inductor discs, each with two Pidgeon inductors. They are oriented as in the original Pidgeon patent, so the inductors on the two discs cross each other without touching directly.
6 · Horseshoe auxiliary inductors
Two auxiliary inductor discs sit on the outside, one beyond each Pidgeon disc. Each auxiliary inductor is shaped like an inflated 3D horseshoe, made of aluminium foil and set inside the dielectric. The left auxiliary disc has 12 inductors in four groups of three; its bottom-left and top-right groups are connected together. The right auxiliary disc has 16 inductors in four groups of four.
7 · Pidgeon inductor wiring
Rightmost Pidgeon inductor: to the top-left group and to the connected bottom-left/top-right groups on the left auxiliary disc. Left Pidgeon inductor on the right-hand disc: to the bottom-right group on the left auxiliary disc, the first jar's outer-foil lead, and the left rotor bottom-side sector contact. Right Pidgeon inductor on the left-hand disc: to the top-left, bottom-right, and bottom-left groups on the right auxiliary disc, with a branch to a stationary contact on the right rotor. Most-left Pidgeon inductor: to the top-right group on the right auxiliary disc. Every sector lead ends in a stationary contact that touches sectors only as they pass.
8 · Wiring groups on the right auxiliary disc
The right auxiliary disc's top-left, bottom-right, and bottom-left groups connect together to the right Pidgeon inductor on the left-hand Pidgeon disc and its branch to a stationary right-rotor sector contact. Its top-right group connects to the most-left Pidgeon inductor.

These captions describe the connections you specified. The sketch does not establish the machine's full operating sequence or verify its electrical behavior.

Before any experiment

High-voltage safety comes first

Electrostatic machines can produce painful or dangerous shocks and can retain charge in their capacitors after they stop. This overview is a reminder, not an operating procedure or a substitute for qualified supervision and local lab rules.

  • Treat the machine, jars, electrodes, and every connected conductor as energized until a qualified person has verified otherwise.
  • Keep hands and bystanders clear while it is operating. Use an appropriate enclosure or barrier and follow the site’s high-voltage procedures.
  • Stored charge can remain after rotation stops. Isolate the drive and follow the manufacturer’s rated discharge and verification procedure before inspection or adjustment.
  • Use only purpose-rated, correctly rated instruments and accessories. Do not improvise probes, grounding leads, or discharge tools.
  • Keep the equipment away from flammable vapors, combustible dust, and oxygen-enriched atmospheres; sparks can ignite them.
  • Do not operate without trained supervision, a documented risk assessment, and a clear emergency stop procedure. If uncertain, do not energize it.

The output calculator is theoretical. Never use its estimates to select test equipment or decide that a machine is safe to touch.

Lineage

Similarities to the Wimshurst and Pidgeon machines

All three are influence machines: instead of rubbing, a tiny stray charge is multiplied by electrostatic induction on every turn.

1883

Wimshurst machine

Two insulated disks with metal sectors spin in opposite directions. Brushes on neutralizer bars induce charge, collecting combs pick it up, and Leyden jars store it until it jumps the spark gap.

Wikipedia: electrostatic generator

1898

Pidgeon machine

W. R. Pidgeon added fixed inductors next to the neutralizer brushes and embedded the sectors in the disks to cut leakage. It combines Wimshurst and Voss ideas and is reported to give at least double the output.

Wikipedia: W. R. Pidgeon

This machine

What it shares — and what's new

Shares the counter-rotating disks, collector combs and Leyden jars of the Wimshurst, and the dielectric-set sectors and crossed Pidgeon inductors of the Pidgeon. New so far: jar inner foils connected to the collector outputs, the first jar's outer foil connected to a stationary contact on the right rotor, and four-group horseshoe auxiliary discs wired to the Pidgeon inductors.

Side-by-side comparison

FeatureWimshurstPidgeonThis machine
Disks2 counter-rotating2 counter-rotating2 counter-rotating rotors
SectorsMetal foil on the outer facesEmbedded in the disk32 per rotor, in the dielectric
Fixed inductorsNoneNext to the neutralizer brushes2 inductor discs × 2 Pidgeon inductors, crossing without touching
CollectionCombs to Leyden jarsCombs to Leyden jarsTop comb is the positive output; bottom comb is the negative output to the Leyden-jar inner foils
Auxiliary inductorsNoneNoneInflated 3D horseshoes of aluminium foil inside the dielectric, wired to the Pidgeon inductors
Feedback to rotorNoneNoneStationary contacts touch passing sectors: the first jar's outer foil reaches the right rotor below and offset from its comb, the left rotor's bottom side, and the left Pidgeon inductor on the right-hand disc; Pidgeon leads contact left-rotor sectors near the upper-left and lower-left

Historical details come from Wikipedia's electrostatic generator article and Antonio Carlos M. de Queiroz's electrostatic machines pages (UFRJ). Pidgeon was granted British Patent 15,100 in 1899, according to Douglas Self's museum of electrostatic generators.

Interactive charge cycle

Follow charge through a classic influence machine

The live model combines a Wimshurst neutralizer cycle with Pidgeon inductors. Use the controls to compare machine modes, change disk speed, pause, or restart; select a step below to follow the charge sequence. This is the established reference cycle, not a claim that the full operating sequence of this custom machine has been specified.

Machine
Voltage across the gap0
Current
0 µA
Power
0 W
Sparks
0
Time to first spark
—

Estimated values for a typical machine with a 3 cm spark gap (about 90 kV). The Pidgeon is set to about twice the Wimshurst's current.

Neutralizer brush   Fixed inductor   Collector comb

Step 1 of 6

Seed charge

A tiny random imbalance on the sectors is enough to start.

Mini game

Spin the machine

Grab the rotor and spin it in circles, or hold the crank button. The faster you spin, the more current it makes. Charge builds in the Leyden jars until a spark jumps the gap. Try to beat your best power.

Drag around the rotor in circles to spin it

Rotor speed0 rpm
Voltage0 kV
Current
0 µA
Average power
0 W
Sparks
0
Last spark energy
—

Your best power: —

Estimated values from a simple Pidgeon-type model: current rises with speed once the machine self-excites, the jars store about 400 pF, and air breaks down at about 30 kV per cm. These aren't measurements of this design.

Intellectual property

Patent application in preparation

The inventor is preparing a patent application for this machine. Please don't copy, manufacture or sell it without written permission. For licensing, partnering or investing, use the contact details below.

Reference

Glossary of terms

Select a term to open its explanation. Select it again to close it.

Before any experiment

Safety checklist

Work through every item before each experiment. Print this page or save it as a PDF using your browser's print dialog.

Before powering on
During operation
After stopping

This checklist supplements the safety guide. It does not replace a site-specific assessment.

Further reading

References and sources

Sources for the Pidgeon machine history are not yet listed here. Original Wimshurst and Pidgeon papers and patents should be checked directly before citing them.